基于系统性能的近地告警技术研究

基于多种导航信息综合处理、告警计算的近地告警系统，对于避免可控撞地事故、 提升飞机安全具有重要意义。本文首先介绍了近地告警系统的工作原理，研究了基于 SOC 曲线的告警包线设计技术，并以过大近地速率告警模式为例进行了告警包线的仿真。最后，利用实际飞行数据分析验证了告警包线合理性以及导航信息可靠性对系统性能的影响。     

济阳坳陷下古生界潜山油气藏特征及成藏模式

济阳坳陷下古生界潜山具有多样性、复杂性的特点，潜山差异性的形成演化、油气成藏主控因素和控藏模式不明确，严重制约了该区潜山油气勘探。在潜山分类的基础上，综合利用系统恢复、分类对比和典型解剖等方法，揭示了济阳坳陷下古生界不同类型潜山的形成演化过程和油气成藏主控因素差异性，分类建立了油气成藏模式。研究表明，济阳坳陷下古生界主要发育高位新盖侵蚀残丘潜山、中位古盖拉张断块潜山、中位新古盖拉张剪切断块潜山、中位中古盖挤压拉张断块潜山和低位古盖拉张滑脱断块潜山5种潜山类型。不同类型潜山的形成演化和油气成藏各具特色，其中，高位新盖侵蚀残丘潜山的发育受隆升、侵蚀作用控制，油气成藏主要受控于油源和盖层条件，表现为"单向供烃、砂体-不整合岩溶体联合输导、残丘控藏"的成藏模式；中位古盖拉张断块潜山的发育受掀斜、断裂作用控制，油气成藏主要受控于储集条件，表现为"单向供烃、顺向断层输导、反向断层控藏"的成藏模式；中位新古盖拉张剪切断块潜山的发育受反转、翘倾和走滑切割作用控制，油气成藏主要受控于输导条件，表现为"多源供烃、断溶体立体输导、断裂控藏"的成藏模式；中位中古盖挤压拉张断块潜山的形成受强烈挤压、拉张滑脱作用控制，油气成藏主要受控于储集条件，表现为"多源供烃、断缝体输导、断褶控藏"的成藏模式；低位古盖拉张滑脱断块潜山的形成受强烈拉张滑脱作用控制，油气成藏主要受控于输导条件，表现为"顶部供烃、断缝体输导、断裂控藏"的成藏模式。     

响应面法优化艾叶挥发油的提取工艺及其抗氧化性能研究

以艾叶挥发油提取率为考核指标,采用单因素实验考察浸泡时间、料液比、提取时间等对艾叶挥发油提取率的影响,在此基础上,采用响应面法优化艾叶挥发油的共水蒸馏提取工艺,并通过紫外分光光度法测定艾叶挥发油对DPPH自由基的清除率来评价其抗氧化性能。结果表明,艾叶挥发油的最佳提取工艺条件为:浸泡时间1.5 h、料液比1∶10(g∶mL)、提取时间4.5 h,在此条件下,艾叶挥发油提取率最高,为0.83%。当艾叶挥发油浓度为80 mg·mL~(-1)时,DPPH自由基清除率最高,为39.12%。表明艾叶挥发油具有一定的抗氧化活性。     

In situ Raman spectroscopic study towards the growth and excellent HER catalysis of Ni/Ni(OH)2 heterostructure

The electrochemical water splitting to produce H₂ in high efficiency with earth-abundant-metal catalysts remains a challenge. Here, we describe a simple “cyclic voltammetry + ageing” protocol at room temperature to activate Ni electrode (AC-Ni/NF) for hydrogen evolution reaction (HER), by which Ni/Ni(OH)₂ heterostructure is formed at the surface. In situ Raman spectroscopy reveals the gradual growth of Ni/Ni(OH)₂ heterostructure during the first 30 min of the aging treatment and combined with polarization measurements, it suggests a positive relation between the Ni/Ni(OH)₂ amount and HER performance of the electrode. The obtained AC-Ni/NF catalyst, with plentiful Ni–Ni(OH)₂ interfaces, exhibits remarkable performance towards HER, with the low overpotential of only 30 mV at a H₂-evolving current density of 10 mA/cm² and 153 mV at 100 mA/cm², as well as a small Tafel slope of 46.8 mV/dec in 1 M KOH electrolyte at ambient temperature. The excellent HER performance of the AC-Ni/NF could be maintained for at least 24 h without obvious decay. Ex situ experiments and in situ electrochemical-Raman spectroscopy along with density functional theory (DFT) calculations reveal that Ni/Ni(OH)₂ heterostructure, although partially reduced, can still persist during HER catalysis and it is the Ni–Ni(OH)₂ interface reducing the energy barrier of H1 adsorption thus promoting the HER performance.     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。     

铸态Ti-20Zr-20Al钛合金动态压缩力学性能与断裂机制研究

采用X射线衍射仪、金相显微镜、分离式霍普金森杆和扫描电镜等手段研究了Ti-20Zr-20Al钛合金在动态压缩条件下的微观结构、力学性能和断裂机制。结果表明,Ti-20Zr-20Al铸态合金由Zr基体相和TiAl/Ti₃Al针状相组成; 随着应变率增加,合金的抗压强度增加,失效应变显著增加; Ti-20Zr-20Al合金的断裂机制为解理断裂; 随着应变率增加,试验压缩断裂后碎片总数增大,平均粒径减小。采用DID模型模拟的材料碎片尺度与实验结果比较吻合,Grady模型与实验结果的偏差较大。     

基于旋翼负压混合吸附的爬壁清洗机器人系统动力学性能研究

针对爬壁清洗机器人越障时,负压装置的吸附力下降导致吸附不稳定的问题,设计了一种旋翼负压混合吸附工作的多边形履带清洗机器人,并对爬行稳定性及越障性能进行了动力学分析。首先根据机器人爬壁的运动原理,建立机器人沿玻璃幕墙上的动力学模型,计算出电机理论驱动力矩;其次分析机器人在跨越障碍过程中的运动模型,结合与壁面接触的实际受力状态,对越障过程中关键阶段的本体倾翻、滑移两种失效形式进行运动学和动力学分析;然后根据玻璃幕墙实际的障碍高度,确定多边形履带的参数和理论驱动力矩的大小,并研制了实验样机进行爬行和越障试验,结果表明所设计的机器人具有良好的越障性能。     

Formation of a protective layer against corrosion on Mg alloy via alkali pretreatment followed by vanillic acid treatment

Although Mg alloy possesses high specific strength, low density, and good biocompatibility, poor corrosion resistance hinders its further applications. In the present study, an innovative protective layer against corrosion was prepared on the AZ31 Mg alloy via alkali pretreatment followed by vanillic acid treatment. The alkali pretreatment supplied –OH for the AZ31 Mg alloy surface to react with vanillic acid. The vanillic acid treatment played a crucial role in enhancing the corrosion resistance due to the excellent ability to act as a barrier and retard aqueous solution penetration, which effectively isolated the underlying Mg alloy from the corrosive environment. The corrosion current density of alkali and vanillic acid-treated Mg alloy (AZ31V) almost showed two orders of magnitude lower values in comparison with that of the AZ31 Mg alloy, and the corrosion potential of AZ31V Mg alloy increased from −1.41 to −1.25 V. The immersion tests proved that there was no occurrence of severe corrosion. Hence, the alkali pretreatment and vanillic acid treatment may represent a promising method to improve the corrosion resistance of Mg alloy.